(DT) 1S28 1800 London Kings Cross to Edinburgh (V1)
21st June 2021This scenario simulates the 1S28 18:00 LNER departure from London Kings Cross to Edinburgh in 2018. The stops enroute are York, Darlington, Newcastle, Berwick and Edinburgh.
**Requirements**
Armstrong Powerhouse (armstrongpowerhouse.com):
Class 91 EP
Class 43 MTU EP
Class 156
Class 158 Cummins EP
Class 313
Class 170 EP
AlanThomsonSim (alanthomsonsim.com)
ECML merge
Updated Voyager Consists
Clowes’ Ex-EMT EMR class 158 reskin
Just Trains (justtrains.net):
Voyager
DTG/RSC:
East Coast Mainline South (for the class 365)
RF72 (dpsimulation.org.uk/rf72emu.html):
Class 365 GTR GN livery
MJW (major.wales/home):
Class 91 VTEC/LNER livery pack
Class 43 VTEC/LNER/EMR livery pack
ash992478 (vulcanproductions.co.uk/ash992478-reskins.html):
Class 170 Scotrail livery pack
**Installation**
Here’s a step-by-step tutorial on installing this scenario.
1. Copy the “Content” folder included in your download.
2. Navigate to your “Railworks” folder. This can vary depending on your PC but it’s likely to be located in Program Files (x86)/Steam/steamapps/common/RailWorks.
3. Paste the previously coppied folder.
That should be it.
You are missing quite alot of things from the requirements
Hi buddy what else is missing as im in the process of downloading
Superalbs 700 is a requirement
Had a look at the scenario again. The headcode of the service causing the issue is 2V22 Moorgate to Welwyn Garden City. It is stationary at green signal K531. I am brought to a stop at the signal prior to the K527. This is either side of the tunnel to the north of Hadley Wood station.
I hope this helps.
I’ve double checked the scenario and, as far as I can see, there aren’t any problems on my end. The only advice I can give is to make sure you have all of the requirements and reinstall the scenario. Sorry.
No problem. Thanks for looking. I’ll have a poke around and see what I can find. As far as I can see, I have all the requirements. I have checked them all and there doesn’t seem to be anything amiss.
I have re-downloaded the scenario afresh and run it again but sadly I still can’t get any further than previous. Stationary at signal K527 behind 2V22.
Of interest though when I load it, I get a scenario failed to load error which I can press F2 to get out of. Not sure if it is relevant though. There are 3 messages on it. Not sure if anyone else has got this one as well or if it is just me. I wouldn’t even like to hazard a guess as to what may be causing this particular error.
Driver 1M76 ‘EDB – BHM’ at Lat 53.99185 Long – 1.13533 – Many failures – See Log Notes (wherever these are)
Driver 1M72 ‘NCL – BHM’ at Lat 53.98299 Long – 1.12687 – Unknown error
Driver 1M76 ‘NCL, BHM’ at Lat 53.98299 Long – 1.12687 – Missing Marker – Doncaster – Platform 3B
Downloaded this scenario as wanted to give it a try. However, only managed to make it as far as just North of Hadley Wood Station and a red signal. There is a pair of 313’s stationary just the other side of the tunnel sat at a green signal on the north bound fast line.
Tried removing the scenario and downloading again and the same issue occurs. Any ideas?
I’m not entirely sure what the problem is here. I’ve tested it multiple times and never had this issue. I’ll double check the scenario and might update the scenario later if I find anything.
Could you perhaps check what the headcode of the service causing the issue is?
I ran the scenario in 2 days, as did Oscar, Firstly KX to Newcastle, then Newcastle to Edinburgh.
Problem free and most enjoyable. Thank you.
Thanks for the feedback! I’m glad you enjoyed it.
Clowes’ Class 158 EX-EMR EMT reskin is also a requirement.
Oh, sorry. I’ll add that to the requirements list. Thanks for pointing it out. 🙂
Did the whole thing in two days-very much enjoyable