(wg) 1F23 1733 London Euston – Liverpool Lime Street (Full Journey)
12th November 2020Drive the 1733 service from London Euston to Liverpool Lime Street, making stops at Rugby, Stafford, Crewe and Runcorn along the way. You will then run the empty stock from Liverpool Lime Street to Edge Hill Intercity Depot. You will be using 390122 in face mask livery. This scenario uses WCML South (DTG Version), WCML Trent Valley and WCML Midlands & North West (Missing Link). This scenario uses the Class 390 included with WCML South, not the discontinued Virgin Trains version.
Requirements: (*=non-essential)
Steam:
Class 159
Class 170
Class 57 Freightliner*
Class 66 V2
Class 67
Class 68
Class 801
Class 92
North Wales Coastal: Crewe – Llandudno (discontinued but can still be bought with TS2018 from various Steam Key vendors)
Portsmouth Direct Line
WCML South
Armstrong Powerhouse:
Class 156
Class 158/159 Enhancement Pack
Class 170 Enhancement Pack
Class 319 Pack Volume 1
Class 350 Enhancement Pack
Class 377 Enhancement Pack
Class 390 Sound Pack
Class 66 Enhancement Pack
Class 67 Enhancement Pack
Class 68 Enhancement Pack
Class 90/Mk3 DVT Pack
Class 92 Sound Pack
FSA/FTA Wagon Pack
JNA-C Wagon Pack
JXA/POA Wagon Pack
JustTrains:
Class 153
Class 20 Advanced (For RHTT)
Class 67 & Car Carriers*
Major Wales Design:
Avanti Class 390 Livery Pack
Class 153 Transport For Wales
Alan Thomson Sim:
Class 319: London Midland/LNWR Livery Pack
Class 66 Freightliner Pack
Class 66 GBRf 2018+
DB Cargo Class 90 Pack
Ex-Virgin Class 221
FS Class 185
PenninePacer Manchester Stations to Huddersfield
Transport For Wales Class 158
Backdated Train Sim:
Statesman Rail Mk2 Pack*
Virtual District Line
Superalbs:
Class 57 – DRS Flash Blue-Green*
TPE Class 802
UKTrainSim:
[TSted] Class 323 Reskin Pack
Vulcan Productions:
Class 170 XC Website livery
This scenario should take about 150 minutes to complete, including the empty stock run at the end. If there are any issues please tell me in the comments
Enjoy!
Part 3 is causing Train sim to black screen and not response unlike the 3 other parts. any Idea why this is ? Also allows me to resume part 3 eventhough Ive just installed it.
All working now, thanks for advice. Cheers.
Glad I could help, enjoy the drive
lat51.52855 long 0.13379- Missing marker (s)siding1
Try redownloading the scenario. If that doesn’t work you can go into the scenario editor and delete the instruction for 1F23 that uses it. It’s just a waypoint used by the player service to avoid a small wrong line working outside Euston so the scenario should still be playable without it
Hi I have all requirements, but when it loads a black box appears suggesting scenario failed to load, unknown error say missing markers etc. Please advise.
Which markers are missing?
Hi
Scenario & stock load fine, but player train wont respond to any keyboard controls or when using the mouse to use the cab controls! (lights, wipers driving controls). Only tried part 1 so dont know if its the same with parts 2 & 3.
Hmmm, as far as I know the AP 390 sound pack changes the cab setup procedure so it could be an issue with the sound pack install. Have you installed the sound pack since WCML South was released to apply the pack to the new 390 bundled with the route?
Did a reinstall of the soundpack & scenario which has done the trick. Cheers for the help.
Glad to hear, enjoy the scenario