(TrainDriverGamer) 5B26 0819 Edinburgh Waverley to Polmadie Depot V2
21st February 2026V2 (yet another update. hopefully the last! thanks again to those that commented to let me know of the issues. If you downloaded the previous versions please redownload this one.)
Set on the 20th Feb 2026, Caledonian Sleeper service 1B26 is at Edinburgh having ran from London Euston with a detachment at Carstairs with half the set going to Glasgow Central. Â
Â
Our job is to take this part of the set from Waverley to Polmadie Depot as 5B26 for stabling so it can be cleaned and prepped before tonight’s service back to London. Â
Â
Set up 92038 and press CTRL + G to set up the GSMR. Â
Â
Max speed on route is 80mph and points at Polmadie Depot are manual so ensure the route is set for the correct road before entering the Depot. Â
Â
Requirements:Â
Â
Route: West Coast Mainline – NW & Scotland Â
Â
Stock:Â
Â
Armstrong Powerhouse:
Class 92 EPÂ
AP Class 321Â
AP Class 318Â
AP Class 390 Sound PackÂ
AP Class 158 EPÂ
AP HST MTUÂ
AP Class 222 EP
Just Trains MeridianÂ
AP Class 800 EP
AP Class 170 EP
AP Weather Pack for correct weather to show
Â
Others:
Class 92
Maxtracks MK5 Coach packÂ
DTG Class 801Â
Glasgow Dunblane Route (for the class 385)Â
DTG Class 390Â
MJW Class 390 Revamp pack
Â
Enjoy 🙂 Â
TrainDriverGamer
V2 ran perfectly. Thank you for a most enjoyable scenario.
Phew! Thanks again for letting me know about the issues.
Seem fated with this one. V1.1 Got as far as Carstairs jcn and got game over due to a collision with 1M09 and 5M01.
Sorry.
thanks for the info. No idea why thats now happened as i never changed their paths in the update. I’ll look into it and either do yet another update or take it down. thanks again.
So sorry to cause you the extra work. Maybe it is my installation, especially if no one else is having the same problem. I will look forward to running again if you decide to update. Thank you.
no its fine, i have amended the paths of the trains you mentioned so hopefully when i upload the update they dont cause the issue from before.
Thanks
All went well until approaching Motherwell, head on crash with an EMU leaving Motherwell.
Hi, Was it a scotrail 385 that was on your track between shieldmuir and motherwell? I found a pathing issue that i must of done when imade some tweaks after after i tested it. If it is that one 2B83 i set it to path via a line before its shieldmuir stop so it passed the platform then reversed back to serve it. i have sorted that and will release the updated version. thanks for letting me know.
Thank you for your reply, yes it was a Scotrail 385 as you say, I believe 2B83 on the same track as me between Motherwell and Shield Hall.
Also required is the Class 320 2022 Scotrail Saltire reskin:
https://get-geeky.weebly.com/reskins.html
I had to swap out the CS Class 92, it didn’t exist on my hard drive
Check your installation, it looks odd:
Class92\CS_AP\92_W2_5_1B26.xml
Nice scenario!
Hi, Didn’t realise i selected that 321 reskin. I have changed it to the standard one included in the 321 pack from AP. The class 92 i think was part of a preset consist but i have changed it for a standard one. Its only stationary in the depot so was not needed to run the scenario. I will upload an updated version. Thanks for letting me know.