1P15 0716 Dover Priory to London Victoria
8th December 20241P15 0716 Dover Priory to London Victoria
Drive a Class 375 train from Dover Priory to London Victoria. You will couple with another unit at Faversham before continuing with the full eight-car unit to the capital. The morning rush hour has begun, so expect possible delays due to traffic in London.
You will be calling at:
Dover Priory – Kearsney – Shepherds Well – Snowdown – Aylesham – Adisham – Bekesbourne – Canterbury East – Selling – Faversham – Teynham – Sittingbourne – Newington – Rainham – Gillingham – Chatham – Rochester – Bromley South – London Victoria.
Scenario Requirements:
Armstrong Powerhouse:
-
Class 375/377 Enhancement Pack
-
Class 377/379/387 Enhancement Pack
-
Class 465/466 Enhancement Pack Vol. 2
-
Class 700/707/717 Enhancement Pack
-
Signal Enhancement Pack
-
Cloud Enhancement Pack (Non-Essential)
-
Sky & Weather Enhancement Pack 2.0 (Non-Essential)
Steam:
-
Train Simulator: London-Faversham High-Speed Route Add-On
-
Train Simulator: Chatham Main & Medway Valley Lines Route Add-On
-
Train Simulator: Chatham Main Line: London Victoria & Blackfriars – Dover & Ramsgate Route Add-On
Please note there may be associated requirements with the list above
This scenario has been created using a real working timetable, therefore there is a substantial amount of AI trains. Furthermore, this scenario assumes the driver will drive in a ‘realistic’ manner (i.e. gradual increments in power on departure etc.) therefore it is advisable that you ignore the ETA section and drive to the best of your ability while trying to maintain the real timetable.
I’m getting this error on loading
Scenario failed to load
Scenario- Broken consist found: – Long: 0.610783 Lat: 51.368604 Driver ‘9P16 0830 Rainham (Kent) to Luton’ at Lat 51.36660 Long 0.61078- Unknown error- Driver “9P16 0830 Rainham (Kent) to Luton’ at Lat 51.36660 Long 0.61078 – Invalid Consist-
Any ideas why and how to fix it?
That isn’t an issue I am too familiar with I’m afraid. I don’t think that I used any other assets that aren’t listed above. My only suggestion to fix it would be to swap the stock in TS tools and see if that still works.
i am a big fan of ur yt
omg this scenario is the best because i love dover to victoria. i always play the route and i love this scenario.
Hello. Thanks for this. But after installation the scenario is called :
1P16 0712 Ramsgate and Dover Priory to London Victoria
and not “”””1P15 0716 Dover Priory to London Victoria””””
I see thank you! I probably got confused because the train is 1P15 to Faversham where it couples up to become 1P16. Will update the file in due course.
Update: All fixed, had to delete the whole route file and re install, all working now (Y)
Okay, nice. Hope it was worth all the trouble in the end 🙂
I have reset the cache, deleted the route and scenario and then re installed both of them back onto the game but still not joy, I dont know what is going on here, even tho I am looking at the right route
I see thank you! I probably got confused because the train is 1P15 to Faversham where it couples up to become 1P16. Will update the file in due course.
Hello, the scenario is not showing up in the standard mode list whilst in the games, any ideas ?
I am not sure about that I’m afraid. I deleted it and redownloaded it on my computer and it shows up. My main suggestion would be to double-check that you are looking at the [Train Simulator: Chatham Main Line: London Victoria & Blackfriars – Dover & Ramsgate Route] rather than the old Chatham Main Line. The scenario is titled 1P15/6 Dover and Ramsgate to London Victoria